I am using a Yamaha RX-V675 receiver. It's connected to an advanced power strip. I am not sure what is the best way of turning off/on my receiver. If I use the receiver's power button, receiver goes into standby. If I want to save energy (trying to be environmentally responsible, not trying to save money), I need to turn off the power strip. In this case no power goes to my receiver. It's a receiver I use almost daily. Now, my question is which one is better for my receiver: to leave it on standby or turn the power completely off. Will turning the power off every time on the power strip (once a day) shorten the life of my receiver. Thank you.
Most of us just keep it in standby mode.
It's okay either way.
I wouldn't worry about it.
AVR draws very little current in the Stand-By mode.
Note that if plugged into a power strip and the strip is OFF for an extended time such as >2 weeks U may lose the station presets, EQ & surround settings..
Power consumption on your avr in various standby modes:
Standby Power Consumption
HDMI Control Off, Standby Through Off
[U.S.A. and Canada models] . 0.10 W or less
[Other models]. 0.15 W or less
HDMI Control On, Standby Through On (No Signals)
. 3 W or less
Network Standby On . 3 W or less
ps I just leave mine in minimal standby
Last edited: Jan 20, 2019My Marantz is rated for less than .5w in standby, much as Lovin' just posted .
I agree with your concerns in general, but there are better ways to address them.
Now if you are the guy that unplugs EVERYTHING you aren't using from TV to Nightlight, and you NEVER leave your phone charger plugged in (which draws current even when a phone isn't attached), you've changed to the most efficient LED lightbulbs that you only use as absolute necessity, and your electricity meter NEVER spins except for when your fridge is running, then sure. unplug your AVR.
(Now of course this already assumes that you are a vegan that only rides a bike, doesn't smoke or burn a candle, or use a fireplace or start a campfire. I should probably stop now. just feeling frisky. sorry.)
I always leave everything that has a standby mode in the standby mode. Running a decent surge arrest and have never lost a component to a surge (knock on wood).
My Marantz is rated for less than .5w in standby, much as Lovin' just posted .
I agree with your concerns in general, but there are better ways to address them.
Now if you are the guy that unplugs EVERYTHING you aren't using from TV to Nightlight, and you NEVER leave your phone charger plugged in (which draws current even when a phone isn't attached), you've changed to the most efficient LED lightbulbs that you only use as absolute necessity, and your electricity meter NEVER spins except for when your fridge is running, then sure. unplug your AVR.
(Now of course this already assumes that you are a vegan that only rides a bike, doesn't smoke or burn a candle, or use a fireplace or start a campfire. I should probably stop now. just feeling frisky. sorry.)
I like your sense of humor. Based on the feedbacks I am getting here, my AVR stays on standby. Thanks all.
I like your sense of humor. Based on the feedbacks I am getting here, my AVR stays on standby. Thanks all.
and see what your system is doing in various modes and other small appliances. Well worth it. Very accurate as well according to CU.
Hey guys, as far as Standby the last thing I am worried about is the cost to provide a trickle of power to my RECENT Yamaha 9.2 Atmos A/V Receiver! I say recent because it's now gone with a brownout we had yesterday. Just had to spend $1,700 for a new A/V receiver. I have four Furman's, one on each powered sub, my 82" TV, and on my Receiver and the stuff it powers. I was always worried about spikes and lightning, but hate admit I never knew a Brownout could fry a receiver. When the new one comes, the first thing I am going to do is stop that HDMI enabled standby. And I also need to buy a APC UPS Powershute like I have on my computers, and put it downstream from by Furman on my new receiver. I subscribe to Audioholics and appreciate all the advice and now I need some on the best UPS to buy -- I see Schneider Electric has one for about $180 -- Help?
Last edited: Feb 14, 2021Hey guys, as far as Standby the last thing I am worried about is the cost to provide a trickle of power to my RECENT Yamaha 9.2 Atmos A/V Receiver! I say recent because it's now gone with a brownout we had yesterday. Just had to spend $1,700 for a new A/V receiver. I have four Furman's, one on each powered sub, my 82" TV, and on my Receiver and the stuff it powers. I was always worried about spikes and lightning, but hate admit I never knew a Brownout could fry a receiver. When the new one comes, the first thing I am going to do is stop that HDMI enabled standby. And I also need to buy a APC UPS Powershute like I have on my computers, and put it downstream from by Furman on my new receiver. I subscribe to Audioholics and appreciate all the advice and now I need some on th best UPS to buy -- I see Schneider Electric has one for about $180 -- Help?
Curious if you're using whole-home surge protection or not?Need to look into that as well. The powered subs were rumbling when I got down there, and I shut the power to them off ASAP but now I'm also worried what it might have done to them and my K-horns!